DeWalt D28710 Service Manual download pdf (Page 33)

When using a cable reel, always unwind the cable

completely.

Connecting to the Mains

The mains supply to be used for this machine must

be equipped with a 16 A cut-out fuse with time delay.

Voltage Drops

Inrush currents cause short-time voltage drops.

Under unfavourable power supply conditions, other

equipment may be affected.

If the system impedance of the power supply is lower

than 0.11 ø, disturbances are unlikely to occur.

ASSEMBLY AND ADJUSTMENTS

WARNING: To reduce the risk of

injury, turn unit off and disconnect

machine from power source before

installing and removing accessories,

before adjusting or changing set-ups

or when making repairs. Be sure the

trigger switch is in the OFF position. An

accidental start-up can cause injury.

Removing and Fitting a Cutting Disc

(ﬁ g. 1, 2)

• With the arm in the rest position, use the lip (v)

to slide the guard (o) back. Leave the guard

retracted (fig. 2).

• Press and hold down the spindle lock (p) (fig. 1).

• Rotate the cutting disc (n) until it locks.

• Using the hex key (k), remove the bolt (w) by

turning counterclockwise and then remove the

flat washer (x) and the retaining flange (y) (fig. 2).

• Check that the spacer (z) is in place against the

flange (aa).

• Replace the cutting disc (n). Make sure that the

new disc is placed onto the spacer (z) in the

correct rotational direction.

• Secure the blade with the retaining flange (y), the

flat washer (x) and the bolt (w).

• Move the guard back down and release the

spindle lock (p).

• Adjust the cutting depth as necessary.

Adjusting the Cutting Depth (ﬁ g. 1)

The cutting depth can be adjusted to meet the wear

of the cutting disc.

• Make a dry run with the tool switched off and

check for clearance.

• If adjustment is required, proceed as follows:

• Loosen the lock nut (f) a few turns.

• Turn the depth stop bolt (e) in or out as to

achieve the required cutting depth.

• Tighten the lock nut (f).

WARNING: Always adjust the depth stop

to its original position when replacing the

cutting disc.

Clamping the workpiece in position (ﬁ g. 1, 3)

The tool is equipped with a material clamp (i) (ﬁ g. 1).

• Pull the lever (m) toward the handle (l) (ﬁ g. 3A).

• Push the clamp shaft (bb) forward until the jaw

(cc) is almost touching the workpiece.

• Press the lever (m) toward the jaw (cc) until it

engages with the clamp shaft (bb).

• Rotate the handle (l) clockwise and clamp the

workpiece securely.

• To release the workpiece, rotate the handle (l)

counterclockwise.

WARNING:

• To increase the cutting capacity, place a

spacer block (dd) under the workpiece

(ee). The spacer block should be slightly

narrower than the workpiece (ﬁ g. 3B).

• Support long workpieces using a piece

of wood (ff) (ﬁ g. 3C). Do not clamp the

cut off end (gg).

Quick Travel Feature (ﬁ g. 3A)

The clamp has a quick travel feature.

• To release the clamp, rotate the handle (l) one or

two turns counterclockwise and pull the lever (m)

toward the handle (l).

Setting the Clamping Position (ﬁ g. 3D)

The clamping position can be set to match the

cutting disc.

• Remove the fence bolts (hh) using the hex

key (k).

• Move the fence (h) as required.

• Re-ﬁ t the fence bolts (hh) and tighten them to

lock the fence (h).

ENGLISH

1 2 ... 28 29 30 31 32 33 34 35 36 37 38 ... 135 136

Comments to this Manuals

No comments

DeWalt D28710 Service Manual Page 33

Comments to this Manuals

Related products and manuals for Power tools DeWalt D28710