DeWalt DCD776 Service Manual download pdf (Page 39)

ENGLISH

SAVE THESE INSTRUCTIONS

Chargers

The DCB106 charger accepts 18 V Li-Ion (DCB180,

DCB181, DCB182, DCB183, DCB184 and

DCB185) battery packs.

The DCB107 charger accepts 10.8 V, 14.4V and

18 V Li-Ion (DCB121, DCB123, DCB125, DCB127,

DCB140, DCB141, DCB142, DCB144, DCB145,

DCB180, DCB181, DCB182, DCB183, DCB184

and DCB185) battery packs.

This charger requires no adjustment and is designed

to be as easy as possible to operate.

Charging Procedure (fig. 2)

1. Plug the charger into an appropriate 230 V

outlet before inserting the battery pack.

2. Insert the battery pack (g) into the charger,

making sure the pack is fully seated in the

charger. The red (charging) light will blink

continuously indicating that the charging

process has started.

3. The completion of charge will be indicated by

the red light remaining ON continuously. The

pack is fully charged and may be used at this

time or left in the charger.

NOTE: To ensure maximum performance and life of

Li-Ion batteries, charge the battery pack fully before

first use.

Charging Process

Refer to the table below for the state of charge of

the battery pack.

State of charge–DCB106

charging –– –– –– ––

fully charged –––––––––––––––––

State of charge–DCB107

charging –– –– –– –– ––

fully charged ––––––––––––––––––––

hot/cold pack delay –– –– –– –––––––

HOT/COLD PACK DELAY (DCB107)

The DCB107 charger has a hot/cold delay feature.

When the charger detects a battery that is hot, it

automatically delays charging until the battery has

cooled.

When the charger detects a battery that is cold, it

automatically delays charging until the battery has

warmed.

The red light will continue to blink, but a yellow

indicator light will be illuminated during this

operation. Once the battery has cooled, the yellow

light will turn off and the charger will resume the

charging procedure.

XR Li-Ion tools are designed with an Electronic

Protection System that will protect the battery

against overloading, overheating or deep discharge.

The tool will automatically turn off if the Electronic

Protection System engages. If this occurs, place the

Li-Ion battery on the charger until it is fully charged.

Important Safety Instructions for All

Battery Packs

When ordering replacement battery packs, be sure

to include the catalog number and voltage.

The battery pack is not fully charged out of the

carton. Before using the battery pack and charger,

read the safety instructions below and then follow

the charging procedures outlined.

READ ALL INSTRUCTIONS

• Do not charge or use the battery pack

in explosive atmospheres, such as in the

presence of flammable liquids, gases or

dust. Inserting or removing the battery pack

from the charger may ignite the dust or fumes.

• Never force the battery pack into charger.

Do not modify the battery pack in any way

to fit into a non-compatible charger as

battery pack may rupture causing serious

personal injury.

• Charge the battery packs only in designated

DEWALT chargers.

• DO NOT splash or immerse in water or other

liquids.

• Do not store or use the tool and battery

pack in locations where the temperature

may reach or exceed 40˚C (105˚F) (such

as outside sheds or metal buildings in

summer).

• For best results, make sure the battery pack is

fully charged before use.

WARNING: Never attempt to open

the battery pack for any reason. If

the battery pack case is cracked or

damaged, do not insert it into the

charger. Do not crush, drop or damage

battery pack. Do not use a battery

pack or charger that has received a

sharp blow, been dropped, run over

or damaged in any way (e.g., pierced

with a nail, hit with a hammer, stepped

1 2 ... 34 35 36 37 38 39 40 41 42 43 44 ... 191 192

Comments to this Manuals

No comments

DeWalt DCD776 Service Manual Page 39

Comments to this Manuals

Related products and manuals for Power drills DeWalt DCD776