DeWalt DCD735-XE Instruction Manual download pdf (Page 14)

Hammerdrilling (Fig. 10)

1. Select the desired speed/torque range using the gear shifter to match the speed

and torque to the planned operation. Turn the collar (C) to the hammerdrill

symbol.

IMPORTANT: Use carbide-tipped or masonry bits rated for percussion drilling

only.

2. Drill with just enough force on the hammer to keep it from bouncing excessively

or "rising" off the bit. Too much force will cause slower drilling speeds,

overheating, and a lower drilling rate.

3. Drill straight, keeping the bit at a right angle to the work. Do not exert side

pressure on the bit when drillling as this will cause clogging of the bit flutes and a

slower drilling speed.

4. When drilling deep holes, if the hammer speed starts to drop off, pull the bit

partially out of the hole with tool still running to help clear debris from the hole.

NOTE: A smooth, even flow of dust from the hole indicates proper drilling rate.

MAINTENANCE

WARNING: To reduce the risk of serious personal injury, place the forward/

reverse button in the lock-off position or turn tool off and disconnect battery pack

before making any adjustments or removing/installing attachments or accessories.

An accidental start-up can cause injury.

Lubrication

Your power tool requires no additional lubrication.

Cleaning

WARNING: Blow dirt and dust out of all air vents with clean, dry air at least once

a week. To minimize the risk of eye injury, always wear AS/NZS51337 approved eye

protection when performing this.

WARNING: Never use solvents or other harsh chemicals for cleaning the

non-metallic parts of the tool. These chemicals may weaken the plastic materials

used in these parts. Use a cloth dampened only with water and mild soap. Never let

any liquid get inside the tool; never immerse any part of the tool into a liquid.

CHARGER CLEANING INSTRUCTIONS

WARNING: Shock hazard. Disconnect the charger from the AC outlet before

cleaning. Dirt and grease may be removed from the exterior of the charger using a

cloth or soft non-metallic brush. Do not use water or any cleaning solutions.

Repairs

The charger and battery pack are not serviceable. There are no serviceable parts

inside the charger or battery pack.

To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment

(including brush inspection and replacement) should be performed by certified

service centers or other qualified service organizations, always using identical

replacement parts.

ACCESSORIES

WARNING: Since accessories, other than those offered by DEWALT, have not been

tested with this product, use of such accessories with this tool could be hazardous.

To reduce the risk of injury, only DEWALT, recommended accessories should be used

with this product.

Recommended accessories for use with your tool are available at extra cost from

your local service center. If you need any assistance in locating any accessory, please

contact Stanley Black & Decker, 82 Taryn Drive, Epping, VIC 3076 Australia or call

1800 444 224 or (NZ) 0800 339 258.

MAXIMUM RECOMMENDED CAPACITIES

DCD730-XE DCD735-XE DCD780-XE DCD785-XE

WOOD

Auger 22 mm (7/8") 22 mm (7/8") 22 mm (7/8") 22 mm (7/8")

Paddle 32 mm (1-1/4") 32 mm (1-1/4") 32 mm (1-1/4") 32 mm (1-1/4")

Twist 13 mm (1/2") 13 mm (1/2") 13 mm (1/2") 13 mm (1/2")

Self-feed 35 mm (1-3/8") 35 mm (1-3/8") 35 mm (1-3/8") 35 mm (1-3/8")

Hole saw 50 mm (2") 50 mm (2") 50 mm (2") 50 mm (2")

1 2 ... 9 10 11 12 13 14 15 16

Comments to this Manuals

No comments

DeWalt DCD735-XE Instruction Manual Page 14

Comments to this Manuals

Related products and manuals for Power tools DeWalt DCD735-XE