DeWalt DXCMLA3706056 Use and Care Manual Page 19
- Page / 88
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
19
English
removed. Serious injury could occur from contact with moving
parts. Hot surfaces. Risk of burn. Pump head, and surrounding
parts are very hot, do not touch (see the Hot Surfaces identied
in Fig. 2). Allow compressor to cool prior to servicing.
1. Set the Auto/Off lever to
N
“Off”, shut off the main
power disconnect, and
relieve all air pressure
from the air tank.
2. Remove the belt guard
by removing the 5 screws
(N) using a Phillips head
screwdriver.
3. Mark pump position on
saddle.
4. Loosen the motor mounting screws and slide the motor toward
the air compressor.
5. Remove the belt and replace with a new one.
6. See the Adjusting Belt Tension before tightening motor
mounting screws.
Adjusting Belt Tension
1. Slide motor into original position, line the
motor up with the
mark made earlier on saddle.
2. Tighten two outside motor mounting screws enough to hold
the motor in place for checking pulley and flywheel alignment.
3. The belt should deflect 1/2” (13 mm)at midway between the
pulley and the flywheel when a 10 pound (4.6 kg.) weight is
applied at the midway point.
3. When proper belt tension is achieved, tighten
all four motor mounting screws. Torque to 20-25 ft-lbs
(27.1–33.9 Nm).
NOTE: Once the engine
Downward Force
Deflection
pulley has been moved
from its factory set loca-
tion, the grooves of the fly-
wheel and pulley must be
aligned to within 1/16”
(1.6mm) to prevent exces-
sive belt wear. Verify the
alignment by performing
the following Motor Pulley/
Flywheel - Alignment.
Motor Pulley/Flywheel Alignment
NOTE: Once the motor pulley has been moved from its factory set
location, the grooves of the flywheel and pulley must be aligned to
within 1/16” (1.6 mm) to prevent excessive belt wear.
The air compressor flywheel and motor pulley must be in-line (in the
same plane) within 1/16” (1.6 mm) to assure belt retention within
flywheel belt grooves. To check alignment, perform the following
steps:
1. Set the Auto/Off lever to “Off”, shut off the main power discon-
nect, and relieve all air pressure from the air tank.
2. Remove belt guard.
3. Place a straightedge
against the outside of
the flywheel and the
motor drive pulley.
4. Measure the distance
between the edge of
the belt and the straightedge at points A1 and A2 in figure.
- DXCMLA3706056 1
- Air Compressor 2
- Pump Specifications 2
- Specifications 2
- Hot Surfaces 3
- Important Safety Instructions 3
- SAVE THESE INSTRUCTIONS 4
- Know Your Air Compressor 9
- FEATURES 9
- INSTALLATION 10
- Assembly (Fig. 1) 10
- Compatibility 11
- Location 11
- Wiring Instructions 12
- Grounding Instructions 12
- Air Distribution System 13
- How to Use Your Unit (Fig 3) 14
- Shut-down (Fig. 1) 15
- MAINTENANCE 16
- Maintenance Chart 16
- Checking Air Filter (Fig. 1) 17
- Draining Air Tank (Fig. 3) 17
- Compressor Pump Oil (Fig. 4) 18
- Belt Replacement 18
- Adjusting Belt Tension 19
- Downward Force 19
- Troubleshooting Guide 24
- Troubleshooting Codes 24
- GLOSSARY 27
- Français 30
- AVERTISSEMENT : 30
- CONSERVER CES DIRECTIVES 30
- CONSERVER CES CONSIGNES 36
- POUR UTILISATION ULTÉRIEURE 36
- CARACTÉRISTIQUES (Fig. 1) 36
- Assemblage (Fig. 1) 37
- Compatibilité 38
- Emplacement 38
- Directives de câblage 39
- Directives de mise à la terre 40
- SYSTÈME DE DISTRIBUTION 41
- D'AIR TYPIQUE 41
- Arrêt (Fig. 1) 43
- Programme d’entretien 44
- Remplacement de la courroie 47
- (Fig. 1) 47
- Force descendante 48
- Glossaire 53
- Guide de dépannage 54
- Codes de dépannage 55
- Superficies calientes 59
- GUARDE ESTAS INSTRUCCIONES 60
- PELIGRO: RIESGO DE EXPLOSIÓN 61
- Elementos y accesorios: 62
- Neumáticos: 62
- CARACTERÍSTICAS (Fig. 1) 66
- SAVE THESE INSTRUCTIONS FOR 66
- FUTURE USE 66
- Instalación 67
- Ensamblaje (Fig. 1) 67
- Lubricación y aceite 68
- Compatibilidad 68
- Anclaje del compresor de aire 69
- SISTEMA TÍPICO DE 71
- DISTRIBUCIÓN DE AIRE 71
- Cómo detenerla 72
- Antes de ponerlo en marcha 72
- Procedimiento de asentamiento 72
- Apagado (Fig. 1) 73
- MANTENIMIENTO 74
- Tabla de mantenimiento 74
- REEMPLAZO (Fig. 1) 75
- (Fig. 4) 76
- Correa - Reemplazo 77
- Fuerza hacia abajo 78
- Polea y volante – Alineación 78
- GLOSARIO 83
- EWALT Industrial Tool Co 88
Related products and manuals for Air compressors DeWalt DXCMLA3706056
(7 pages)© 2020, manymanuals.com. All rights reserved. | 1.146 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals