DeWalt DXCMLA3706056 Use and Care Manual Page 12
- Page / 88
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
12
English
mounted.
The air compressor MUST be bolted to a level, solid concrete
surface. Use 3/8” lag screws, vibration pads and concrete
anchors. If help is needed anchoring the air compressor consult
a licensed contractor.
1. Place the air
3/8" Lag
Screw
(not supplied)
Vibration
pad
(not
supplied)
Concrete Anchor
(not supplied)
Surface Line
Shim Under
Vibration pad
(not supplied)
compressor on a
level, solid concrete
surface. Make sure
the concrete is in
good condition with
no cracks or
damage.
2. Mark the surface
using the holes in
the air compressor
feet as a template.
3. Drill holes in the
surface for the concrete anchors. Install concrete anchors.
4. Line-up holes in surface with holes in air compressor feet.
5. Place the vibration pads (not supplied) between the floor and
air compressor feet, see figure. If needed use shims to level
the unit.
6. Place the 3/8” lag screws through the air compressor feet,
vibration pads and into the anchors.
7. Torque 3/8” lag screws to 7-10 ft.-lbs (9.5-13.5 Nm).
Wiring Instructions
WARNING: Improper electrical installation of this product
may void its warranty and your re insurance. Have circuit wiring
performed by qualied personnel such as a licensed electrician
who is familiar with the current national electrical code and any
prevailing local electrical codes.
WARNING: Risk of electrical shock. Improper electrical
grounding can result in electrical shock. The wiring should be done
by a qualied electrician.
A qualified electrician needs to knows the following before wiring:
1. The amperage rating of the electrical box should be adequate.
Refer to the Specifications, in the parts manual, for this
information.
2. The supply line should have the same electrical characteristics
(voltage, cycle, phase) as the motor. Refer to the motor
nameplate, on side of motor, for this information.
NOTE: The wiring used must be rated for the motor nameplate
voltage, plus or minus 10%. Refer to local codes for recommended
wire sizes, correct wire size, and maximum wire run; undersize wire
causes high amp draw and overheating to the motor.
WARNING: Risk of electrical shock. Electrical wiring must
be located away from hot surfaces such as manifold assembly,
compressor outlet tubes, heads, or cylinders.
Grounding Instructions
This product should be connected to a metallic, permanent wiring
system, of and equipment-grounding terminal or lead on the
product.
Voltage and Circuit Protection
Refer to the Voltage and Minimum Branch Circuit Requirements
under Specifications.
CAUTION: Certain air compressors can be operated on a
15 amp circuit if the following conditions are met.
- DXCMLA3706056 1
- Air Compressor 2
- Pump Specifications 2
- Specifications 2
- Hot Surfaces 3
- Important Safety Instructions 3
- SAVE THESE INSTRUCTIONS 4
- Know Your Air Compressor 9
- FEATURES 9
- INSTALLATION 10
- Assembly (Fig. 1) 10
- Compatibility 11
- Location 11
- Wiring Instructions 12
- Grounding Instructions 12
- Air Distribution System 13
- How to Use Your Unit (Fig 3) 14
- Shut-down (Fig. 1) 15
- MAINTENANCE 16
- Maintenance Chart 16
- Checking Air Filter (Fig. 1) 17
- Draining Air Tank (Fig. 3) 17
- Compressor Pump Oil (Fig. 4) 18
- Belt Replacement 18
- Adjusting Belt Tension 19
- Downward Force 19
- Troubleshooting Guide 24
- Troubleshooting Codes 24
- GLOSSARY 27
- Français 30
- AVERTISSEMENT : 30
- CONSERVER CES DIRECTIVES 30
- CONSERVER CES CONSIGNES 36
- POUR UTILISATION ULTÉRIEURE 36
- CARACTÉRISTIQUES (Fig. 1) 36
- Assemblage (Fig. 1) 37
- Compatibilité 38
- Emplacement 38
- Directives de câblage 39
- Directives de mise à la terre 40
- SYSTÈME DE DISTRIBUTION 41
- D'AIR TYPIQUE 41
- Arrêt (Fig. 1) 43
- Programme d’entretien 44
- Remplacement de la courroie 47
- (Fig. 1) 47
- Force descendante 48
- Glossaire 53
- Guide de dépannage 54
- Codes de dépannage 55
- Superficies calientes 59
- GUARDE ESTAS INSTRUCCIONES 60
- PELIGRO: RIESGO DE EXPLOSIÓN 61
- Elementos y accesorios: 62
- Neumáticos: 62
- CARACTERÍSTICAS (Fig. 1) 66
- SAVE THESE INSTRUCTIONS FOR 66
- FUTURE USE 66
- Instalación 67
- Ensamblaje (Fig. 1) 67
- Lubricación y aceite 68
- Compatibilidad 68
- Anclaje del compresor de aire 69
- SISTEMA TÍPICO DE 71
- DISTRIBUCIÓN DE AIRE 71
- Cómo detenerla 72
- Antes de ponerlo en marcha 72
- Procedimiento de asentamiento 72
- Apagado (Fig. 1) 73
- MANTENIMIENTO 74
- Tabla de mantenimiento 74
- REEMPLAZO (Fig. 1) 75
- (Fig. 4) 76
- Correa - Reemplazo 77
- Fuerza hacia abajo 78
- Polea y volante – Alineación 78
- GLOSARIO 83
- EWALT Industrial Tool Co 88
Related products and manuals for Air compressors DeWalt DXCMLA3706056
(7 pages)© 2020, manymanuals.com. All rights reserved. | 1.796 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals