DeWalt D28710 Instruction Manual download pdf (Page 4)

English

resulting in loss of power and overheating. When using more than

one extension to make up the total length, be sure each individual

extension contains at least the minimum wire size. The following

table shows the correct size to use depending on cord length and

nameplate ampere rating. If in doubt, use the next heavier gauge.

The smaller the gauge number, the heavier the cord.

Minimum Gauge for Cord Sets

Ampere Rating

Volts Total Length of Cord in Feet (meters)

120V 25 (7.6) 50 (15.2) 100 (30.5) 150 (45.7)

240V 50 (15.2) 100 (30.5) 200 (61.0) 300 (91.4)

Than

Not More

Than

AWG

0 6 18 16 16 14

610 18 16 14 12

10 12 16 16 14 12

12 16 14 12 Not Recommended

• WEAR PROPER APPAREL. Do not wear loose clothing,

neckties, rings, bracelets, or other jewelry which may get caught in

moving parts. Nonslip footwear is recommended. Wear protective

hair covering to contain long hair. Air vents often cover moving

parts and should also be avoided.

• ALWAYS USE SAFETY GLASSES which meet the ANSI Z87.1

requirements. Also use face or dust mask if cutting operation is

dusty. Everyday eyeglasses only have impact resistant lenses, they

are not safety glasses.

• SECURE WORK. Use clamps or a vise to hold work. It’s safer

than using your hand and it frees both hands to operate tool.

• DON’T OVERREACH. Keep proper footing and balance at all

times.

• MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean

for best and safest performance. Follow instructions for lubricating

and changing accessories.

• DISCONNECT TOOLS before servicing; when changing

accessories, such as blades, bits, cutters, and the like.

• REDUCE THE RISK OF UNINTENTIONAL STARTING. Make

sure switch is in off position before plugging in.

• USE RECOMMENDED ACCESSORIES. Consult the instruction

manual for recommended accessories. The use of improper

accessories may cause risk of injury to persons.

• NEVER STAND ON TOOL. Serious injury could occur if the tool

is tipped or if the cutting tool is unintentionally contacted.

• CHECK DAMAGED PARTS. Before further use of the tool, a

guard or other part that is damaged should be carefully checked

to determine that it will operate properly and perform its intended

function — check for alignment of moving parts, binding of moving

parts, breakage of parts, mounting, and any other conditions that

may affect its operation. A guard or other part that is damaged

should be properly repaired or replaced.

• NEVER LEAVE TOOL RUNNING UNATTENDED. TURN

POWER OFF. Don’t leave tool until it comes to a complete stop.

Additional Safety Rules for Chop Saw

• Always wear proper eye and respiratory protection.

• Before using, inspect the cutting wheel for cracks or flaws.

If such a crack or flaw is evident, discard the wheel. The

wheel should also be inspected whenever you think the tool

may have been dropped. Flaws may cause wheel breakage.

• When starting the tool with a new or replacement wheel

or if you are unsure of the condition of the wheel, hold the

tool in a well protected area and let it run for one minute. If

the wheel has an undetected crack or flaw, it should burst

in less than one minute. Never start the tool with a person in line

with the wheel. This includes the operator.

• In operation, avoid bouncing the wheel or giving it rough

treatment. If this occurs, stop the tool and inspect the wheel for

cracks or flaws.

• Clean your chop saw periodically following the procedure in this

manual.

• Do not remove wheel guards or base.

1 2 3 4 5 6 7 8 9 ... 43 44

Comments to this Manuals

No comments

DeWalt D28710 Instruction Manual Page 4

Comments to this Manuals

Related products and manuals for Power tools DeWalt D28710