DeWalt D25213K Service Manual Page 33
- Page / 140
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
33
E N G L I S H
● Pull on the bit to check if it is properly locked.
The hammering function requires the bit to be
able to move axially several centimetres when
locked in the tool holder.
● To remove a bit pull back the tool holder locking
sleeve (12) and pull out the bit.
@
Always wear gloves when you change
accessories. The exposed metal parts
on the tool and accessory may become
extremly hot during operation.
Fitting the side handle (fig. D)
The side handle (10) can be fitted to suit both
RH- and LH-users.
@
Do not use the tool without the side
handle properly assembled.
● Loosen the side handle.
● For RH-users, slide the side handle clamp over
the collar behind the tool holder, handle at the
left.
● For LH-users, slide the side handle clamp over
the collar behind the tool holder, handle at the
right.
● Rotate the side handle to the desired position
and tighten the handle.
Setting the drilling depth (fig. E)
● Insert the required drill bit as described above.
● Press the depth stop clamp (11) and keep it
depressed.
● Fit the depth adjustment rod (9) through the
hole in the depth stop clamp.
● Adjust the drilling depth as shown.
● Release the depth stop clamp.
Forward/reverse slider (fig. F1 & F2)
D25112(C)K/D25113K/D25114K (fig. F1)
● Push the forward/reverse slider (3) to the
RH-side for forward (RH) rotation. See arrows
on tool.
● Push the forward/reverse slider (3) to the
LH-side for reverse (LH) rotation.
D25213K (fig. F2)
● Push the forward/reverse slider (3) to the
LH-side for forward (RH) rotation. See arrows
on tool.
● Push the forward/reverse slider (3) to the
RH-side for reverse (LH) rotation.
@
Always wait until the motor has come to
a complete standstill before changing
the direction of rotation.
D25112(C)K/D25113K/D25213K -
Fitting the chuck adapter & chuck
● Screw the chuck onto the threaded end of the
chuck adapter.
● Insert the connected chuck and adapter in the
tool as though it were a standard SDS-plus® bit.
● To remove the chuck, proceed as for removing
a standard SDS-plus® bit.
@
Never use standard chucks in the
hammer drilling mode.
D25114K - Replacing the tool holder with the
chuck (fig. G)
● Turn the locking collar (8) into the unlocking
position and pull the tool holder (6) off.
● Push the chuck (13) onto the spindle and turn
the locking collar into the locking position.
● To replace the chuck with the tool holder, first
remove the chuck the same way as the tool
holder was removed. Then place the tool holder
the same way as the chuck was placed.
@
Never use standard chucks in the
hammer drilling mode.
Replacing the dust cover (fig. C)
The dust cover (7) prevents dust ingress into
the mechanism. Replace a worn dust cover
immediately.
● Pull back the tool holder locking sleeve (12) and
pull the dust cover (7) off.
● Fit the new dust cover.
● Release the tool holder locking sleeve.
- D25112(C)K 1
- D25113K 1
- D25114K 1
- Copyright DEWALT 2
- ROTERENDE BOREHAMMER 6
- EU-overensstemmelseserklæring 7
- Sikkerhedsanvisninger 8
- D A N S K 11
- Brugervejledning 12
- Vedligeholdelse 13
- Beskyttelse af miljøet 14
- BOHRHAMMER 16
- D E U T S C H 17
- EG-Konformitätserklärung 17
- Sicherheitshinweise 18
- Überprüfen der Lieferung 20
- Gerätebeschreibung (Abb. A) 20
- Elektrische Sicherheit 20
- Verlängerungskabel 21
- Zusammenbauen und Einstellen 21
- Gebrauchsanweisung 23
- Umweltschutz 25
- E N G L I S H 27
- Congratulations! 27
- Technical data 27
- EC-Declaration of conformity 28
- Safety instructions 29
- Package contents 30
- Description (fig. A) 31
- Electrical safety 31
- Mains plug replacement 31
- (U.K. & Ireland only) 31
- Using an extension cable 32
- Assembly and adjustment 32
- Instructions for use 34
- Maintenance 35
- Protecting the environment 35
- E S P A Ñ O L 37
- ¡Enhorabuena! 37
- Características técnicas 37
- Declaración CE de conformidad 38
- Instrucciones de seguridad 39
- Descripción (fig. A) 41
- Seguridad eléctrica 41
- Montaje y ajustes 42
- Instrucciones para el uso 44
- Mantenimiento 45
- Protección del medio ambiente 46
- MARTEAU ECTROPNEUMATIQUE 48
- F R A N Ç A I S 49
- Déclaration CE de conformité 49
- Consignes de sécurité 50
- Contenu de l'emballage 52
- Sécurité électrique 52
- Câbles de rallonge 53
- Assemblage et réglage 53
- Mode d'emploi 55
- Entretien 56
- I T A L I A N O 58
- Congratulazioni! 58
- Dati tecnici 58
- Norme generali di sicurezza 60
- Contenuto dell'imballo 62
- Descrizione (fig. A) 62
- Norme di sicurezza elettrica 62
- Impiego di una prolunga 63
- Assemblaggio e regolazione 63
- Istruzioni per l'uso 65
- Manutenzione 66
- Protezione dell'ambiente 67
- BOORHAMER 69
- N E D E R L A N D S 70
- Veiligheidsinstructies 71
- Inhoud van de verpakking 73
- Beschrijving (fig. A) 73
- Elektrische veiligheid 73
- Monteren en instellen 74
- Gebruik van verlengsnoeren 74
- Aanwijzingen voor gebruik 75
- Onderhoud 77
- BORHAMMER 79
- N O R S K 80
- CE-sikkerhetserklæring 80
- Sikkherhetsveiledning 81
- Vedlikehold 86
- Miljøvern 87
- MARTELO ELECTROPNEUMÁTICO 89
- P O R T U G U Ê S 90
- Declaração CE de conformidade 90
- Instruções de segurança 91
- Descrição (fig. A) 93
- Segurança eléctrica 93
- Extensões 94
- Montagem e afinação 94
- Modo de emprego 95
- Manutenção 97
- Protecção do meio ambiente 98
- PORAVASARA 99
- S U O M I 100
- Turvaohjeet 101
- Käyttöohjeet 105
- Huolto-ohjeita 106
- Ympäristön suojelu 107
- BORRHAMMARE 109
- S V E N S K A 110
- Säkerhetsanvisningar 111
- Bruksanvisning 115
- Miljöskydd 117
- DARBELİ MATKAP 119
- T Ü R K Ç E 120
- Güvenlik talimatları 121
- Kullanım talimatları 125
- Çevreyi koruma 127
- Ε Λ Λ Ν Η Ι Κ Α 129
- Θερμά συγχαρητήρια! 129
- Τεχνικά χαρακτηριστικά 129
- Οδηγίες ασφαλείας 131
- Ελεγχος του περιεχομένου της 133
- Οδηγίες χρήσεως 136
- Συντήρηση 138
- 495266-00 140
Related products and manuals for Power drills DeWalt D25213K
Power drills DeWalt DCD940 Service Manual
(200 pages)
(200 pages)
Power drills DeWalt DC845-XE User Manual
(36 pages)
(36 pages)
Power drills DeWalt DC720 User Manual
(16 pages)
(16 pages)
Power drills DeWalt DW005 Service Manual
(116 pages)
(116 pages)
Power drills DeWalt DCD945 User Manual
(20 pages)
(20 pages)
Power drills DeWalt DC987 Service Manual
(20 pages)
(20 pages)
Power drills DeWalt DWD010 User Manual
(16 pages)
(16 pages)
Power drills DeWalt DW979 Instruction Manual
(34 pages)
(34 pages)
Power drills DeWalt DWD014 Service Manual
(36 pages)
(36 pages)
Power drills DeWalt D25313 User Manual
(24 pages)
(24 pages)
Power drills DeWalt DC935-XE User Manual
(44 pages)
(44 pages)
Power drills DeWalt DWD024 Service Manual
(40 pages)
(40 pages)
Power drills DeWalt DW505 Instruction Manual
(22 pages)
(22 pages)
Power drills DeWalt DC841 User Manual
(2 pages)
(2 pages)
Power drills DeWalt DW926 Service Manual
(100 pages)
(100 pages)
Power drills DeWalt DCD710 Service Manual
(40 pages)
(40 pages)
Power drills DeWalt D25003 User Manual
(20 pages)
(20 pages)
Power drills DeWalt DCD735-XE Service Manual
(48 pages)
(48 pages)
© 2020, manymanuals.com. All rights reserved. | 1.443 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals