DeWalt D25213K Service Manual download pdf (Page 32)

E N G L I S H

Using an extension cable

If an extension cable is required, use an approved

extension cable suitable for the power input of this

machine (see technical data).

The minimum conductor size is 1.5 mm

When using a cable reel, always unwind the cable

completely.

Also refer to the table below.

Conductor size (mm

) Cable rating (Amperes)

0.75 6

1.00 10

1.50 15

2.50 20

4.00 25

Cable length (m)

7.5 15 25 30 45 60

Voltage Amperes Cable rating (Amperes)

115 0 - 2.0 6 6 6 6 6 10

2.1 - 3.4 6 6 6 6 15 15

3.5 - 5.0 6 6 10 15 20 20

5.1 - 7.0 10 10 15 20 20 25

7.1 - 12.0 15 15 20 25 25 -

12.1 - 20.0 20 20 25 - - -

230 0 - 2.0 6 6 6 6 6 6

2.1 - 3.4 6 6 6 6 6 6

3.5 - 5.0 6 6 6 6 10 15

5.1 - 7.0 10 10 10 10 15 15

7.1 - 12.0 15 15 15 15 20 20

12.1 - 20.0 20 20 20 20 25 -

Assembly and adjustment

Prior to assembly and adjustment

always unplug the tool.

Selecting the operating mode (ﬁg. B1 & B2)

D25112(C)K (ﬁg. B1)

The tool can be used in the following operating

modes:

Rotary drilling: for screwdriving and for

drilling into steel, wood and plastics

Hammer drilling: for concrete and

masonry drilling operations.

D25113K/D25114K/D25213K (ﬁg. B2)

The tool can be used in the following operating

modes:

Rotary drilling: for screwdriving and for

drilling into steel, wood and plastics

Hammer drilling: for concrete and

masonry drilling operations.

Hammering only: for light chipping,

chiselling and demolition applications.

In this mode the tool can also be used

as a lever to free a jammed drill bit.

Bit rotation: non-working position used

only to rotate a ﬂat chisel into the

desired position.

● To select the operating mode, press the safety

lock (5) and rotate the mode selector switch (4)

until it points to the symbol of the required mode.

● Release the safety lock and check that the

mode selector switch is locked in place.

Do not select the operating mode when

the tool is running.

Indexing the chisel position

The chisel can be indexed and locked into

51 different positions.

● Rotate the mode selector switch (4) until it

points to the "bit rotation" position.

● Rotate the chisel in the desired position.

● Set the mode selector switch (4) to the

"hammering only" position.

● Twist the chisel until it locks in position.

Inserting and removing SDS-plus

accessories

(ﬁg. C)

This tool uses SDS-plus

accessories (refer to the

inset in ﬁg. C for a cross-section of an SDS-plus

bit shank).

We recommend to use professional accessories

only.

● Clean and grease the bit shank.

● Insert the bit shank into the tool holder (6).

● Push the bit down and turn it slightly until it ﬁts

into the slots.

1 2 ... 27 28 29 30 31 32 33 34 35 36 37 ... 139 140

Comments to this Manuals

No comments

DeWalt D25213K Service Manual Page 32

Comments to this Manuals

Related products and manuals for Power drills DeWalt D25213K