DeWalt DW089-XE Instruction Manual download pdf (Page 4)

5 6

WALL SET-UP (FIG. 3A)

The keyhole (M) in the pivot bracket (H) is used for mounting to wall

constructions. Alternatively, the tool can be attached to metal studs

directly using the magnets (N).

1. Drive a screw or nail into the wall.

2. Hang the tool onto the fastener by the keyhole.

FITTING THE TOOL TO THE WALL MOUNT (FIG. 3A–3D)

The tool has been equipped with a wall mount (I) for mounting to wall

track to aid in drop ceiling installation and other specialty leveling

projects. The pivot bracket (H) has magnets to attach the tool to the

wall mount.

Align the magnets (N) with the metal plate on the wall mount (I).

To remove the wall mount, pull the wall mount from the tool applying

sufficient force.

To Fit the Wall Mount to Wall Track (FIG. 3B, 3C)

1. Open the clamp jaws (O).

2. Place the clamp jaw around the wall track and release the clamp

to close the clamp jaws shut on the track.

To Mount the Wall Mount to a Wall (FIG. 3D)

1. Reorient the wall mount so the mounting hole (P) is at the top and

the clamp jaws (O) are at the bottom.

2. Hold the tool at the desired position against the wall and mark the

location of the mounting hole (P) on the wall.

3. Drill a hole at the marked location.

4. Insert a corresponding plug into the hole.

5. Hold the tool in front of the plug.

6. Turn a screw into the mounting hole (P).

Adjusting the Tool

To initiate the leveling procedure, switch on the tool. The level and/

or plumb orientation is correctly adjusted as long as the laser beams

remain on.

The laser beams start flashing to indicate that the tool has been set up

at a slope that is beyond the self-leveling range of 4°. Switch the tool

off, re-adjust the tool set-up within the self-leveling range and switch

the tool on again.

FIG. 3B

FIG. 3C

FIG. 3D

FIG. 3A

Aligning the Laser Line (Fig. 4)

Align the laser line of either one of the laser beams with the position

mark. Move the tool as required.

OPERATION

WARNING: Do not place

the laser in a position which

may cause anyone to

intentionally or

unintentionally stare into the

laser beam. Serious eye

injury may result from staring

at the beam.

Instructions for Use

WARNING: Always observe the safety instructions and applicable

regulations.

•Alwaysmarkthecentreofthelaserdots.

•Makesurethetoolhasbeensetupsecurely.

•Extremetemperaturechangescausemovementofinternalpartsthat

may affect the accuracy of the tool. Regularly check the accuracy

while using the tool under these circumstances.

•Althoughthetoolcorrectssmallout-of-levelerrorsautomatically,

when it is bumped, re-adjustment to balance or set-up may be

required.

•Ifthetoolhasbeendroppedorhastippedover,checkwhether

there is damage by performing the field calibration checks. See

Maintenance.

Switching On and Off (Fig. 1)

The tool has separate switches to operate the vertical laser line and

the horizontal laser line.

To switch the vertical laser beam (D) on, press the on/off switch (A).

To switch the horizontal laser beam (E) on, press the on/off switch (B).

To switch either laser beam off, press the on/off switch again.

Transferring a Position Mark (Fig. 4)

The tool produces two laser

lines in horizontal and in

vertical direction, to transfer a

mark.

Align the relevant laser beam

with the mark.

Rotating the Tool (Fig. 5)

When in wall set-up, the tool can

be rotated manually to transfer

the horizontal laser line.

Rotate the tool to the left or right

as required.

Laser Accessories

DE0892-XE DIGITAL LASER

DETECTOR (FIG. 6)

Some laser kits include a DeWALT Digital Laser detector.

The DeWALT Digital Laser Detector helps in locating a

laser beam emitted by the laser in bright light conditions

or over long distances. The detector can be used in

both indoor and outdoor situations where it is difficult to

see the laser beam.

The detector is designed exclusively for use with the DW088-XE and

the DW089-XE line lasers and other compatible DeWALT line lasers. It

is not for use with rotating lasers.

The detector gives both visual signals through the LCD display window

(Q) and audio signals through the speaker (R) to indicate the location

of the laser beam.

The DeWALT Digital Laser Detector can be used with or without the

detector clamp. When used with the clamp, the detector can be

positioned on a grade rod, leveling pole, stud or post.

FIG. 4

FIG. 5

1 2 3 4 5 6 7

Comments to this Manuals

No comments

DeWalt DW089-XE Instruction Manual Page 4

Comments to this Manuals

Related products and manuals for Laser levels DeWalt DW089-XE