DeWalt DW089-XE Instruction Manual download pdf (Page 6)

9 10

SCAN CHECK (FIG. 7)

1. Place the tool in an area between two vertical surfaces that are at

least 9m apart. Mount the tool exactly midway to the wall.

2. Position the tool at an angle of 45° to the left.

3. Switch on the horizontal laser beam.

4. Mark the centre of the laser beam exactly midway on the opposite

wall.

5. Switch off the tool and rotate it 90° clockwise.

6. Switch on the horizontal laser beam.

7. Mark the centre of the laser beam exactly midway on the opposite

wall.

8. Switch off the tool.

9. Measure the difference between the markings.

10. If the difference between the markings is 3 mm or less, the tool is

properly calibrated.

11. If the difference between the markings is more than 3 mm, the tool

must be serviced.

LEVEL CHECK (FIG. 8A, 8B)

1. Place the tool in an area with a wall of at least 9 m length. Mount

the tool to one end of the wall.

2. Position the tool at an angle of 90° to the left.

3. Switch on the horizontal laser beam.

4. Mark the centre of the laser beam at one-third distance (FF) and at

two-third distance (GG) on the wall.

5. Switch off the tool.

6. Mount the tool to the other end of the wall.

7. Position the tool at an angle of 90° to the right.

8. Switch on the horizontal laser beam.

9. Switch on the tool, align the laser beam with the wall marking (GG)

and mark the laser beam at two-third distance (HH) on the wall.

10. Switch off the tool.

11. Measure the difference between the markings (FF, HH).

12. If the difference between the markings is 6 mm or less, the tool is

properly calibrated.

13. If the difference between the markings is more than 6 mm, the tool

must be serviced.

FIG. 8A

FIG. 8B

PLUMB CHECK (FIG. 9A, 9B)

1. Place the tool on the floor in an area with a ceiling of at least 2,5 m

height.

2. Mark a line of 1,5 m length (II) on the floor. Position the tool at one

end of the floor marking (II).

3. Switch on the vertical laser beam.

4. Align the laser beam with the floor marking (II).

5. Mark the centre of the laser beam at one-third distance (JJ) and at

two-thirds distance (KK) on the ceiling.

6. Switch off the tool. Position the tool at the other end of the floor

marking (II) facing the marking.

7. Switch on the vertical laser beam.

FIG. 9A

FIG. 9B

8. Align the laser beam with the floor marking (II).

9. Mark the centre of the laser beam at one-third distance (LL) and at

two-thirds distance (MM) on the ceiling.

10. Switch off the tool.

11. Measure the difference between the markings (JJ, LL).

12. Measure the difference between the markings (KK, MM).

13. If the difference between the markings is 3,5 mm or less, the tool is

properly calibrated.

14. If the difference between the markings is more than 3,5 mm, the

tool must be serviced.

Cleaning

Exterior plastic parts may be cleaned with a damp cloth. Although these

parts are solvent resistant, NEVER use solvents. Use a soft, dry cloth to

remove moisture from the tool before storage.

Repairs

NOTE: Disassembling the laser will void all warranties on the product.

To assure product SAFETY and RELIABILITY, repairs, maintenance and

adjustment should be performed by certified service centers or other

qualified service organizations.

Accessories

WARNING: Since accessories, other than those offered by DeWALT,

have not been tested with this product, use of such accessories with

this tool could be hazardous. To reduce the risk of injury, only DeWALT

recommended accessories should be used with this product.

USING THE LASER WITH ACCESSORIES (FIG. 1 INSET)

The laser is equipped with a 1/4" x 20 female thread (K) on the bottom

of the unit. This thread is to accommodate current or future DeWALT

accessories. Only use DeWALT accessories specified for use with this

product. Follow the directions included with the accessory.

These are:

 • DE0881-XEDeWALT tripod

 • DE0892-XEDeWALT detector

Consult your dealer for further information on the appropriate

accessories.

Recommended accessories for use with your tool are available at

extra cost from your local service center. If you need any assistance

in locating any accessory, please contact Stanley Black & Decker, 82

Taryn Drive, Epping, VIC 3076 Australia or call 1800 444 224 or (NZ)

0800 339 258.

Batteries

When disposing batteries, think of the protection of the environment.

Check with your local authorities for an environmentally safe way of

battery disposal.

1 2 3 4 5 6 7

Comments to this Manuals

No comments

DeWalt DW089-XE Instruction Manual Page 6

Comments to this Manuals

Related products and manuals for Laser levels DeWalt DW089-XE