DeWalt DW703 Service Manual download pdf (Page 26)

Voltage drops

Inrush currents cause short-time voltage drops. Under unfavourable power

supply conditions, other equipment may be affected.

If the system impedance of the power supply is lower than 0.25 ø,

disturbances are unlikely to occur.

Package contents

The package contains:

1 Assembled mitre saw

1 Blade spanner

1 Saw blade, ATB (DW703)

1 Saw blade, TCG (DW702)

2 Clamps (DW702)

1 Instruction manual

1 Exploded drawing

• Check for damage to the tool, parts or accessories which may have

occurred during transport.

• Take the time to thoroughly read and understand this manual prior to

operation.

Description (fig. A1 - A6)

1 Operating handle

2 Moveable lower guard

3 Fence right-hand side

4 Mitre clamp knob

5 Mitre latch

6 Mitre scale

7 Fence left-hand side

8 Bench mounting holes

9 Carrying handle

10 Head lock up release lever

11 Rear lower guard

12 Bevel scale

13 Padlock hole

14 Blade spanner

15 Spindle lock button

16 Trigger switch

17 Bevel clamp handle

18 Head lock down pin

20 Dust spout

21 Angle position stop

22 Hand indentation

23 Upper fence left-hand side clamping knob

24 Upper guard

25 Motor housing

26 Bevel position adjustment stop

27 Kerf plate

28 Vertical position adjustment stop

29 Work support extension

30 Adjustable length stop

31 Work piece clamp

32 Dustbag

en - 3 18

ENGLISH

Your tool is double insulated in accordance with EN 61029;

therefore no earth wire is required.

Mains plug replacement

(U.K. & Ireland only)

• Should your mains plug need replacing and you are competent to do

this, proceed as instructed below. If you are in doubt, contact an

authorized DEWALT repair agent or a qualified electrician.

• Disconnect the plug from the supply.

• Cut off the plug and dispose of it safely; a plug with bared copper

conductors is dangerous if engaged in a live socket outlet.

• Only fit 13 Amperes BS1363A approved plugs fitted with the correctly

rated fuse (1).

• The cable wire colours, or a letter, will be marked at the connection

points of most good quality plugs. Attach the wires to their respective

points in the plug (see below). Brown is for Live (L) (2) and Blue is for

Neutral (N) (4).

• Before replacing the top cover of the mains plug ensure that the cable

restraint (3) is holding the outer sheath of the cable firmly and that the

two leads are correctly fixed at the terminal screws.

Never use a light socket.

Never connect the live (L) or neutral (N) wires to the earth pin

marked E or .

For 115 V units with a power rating exceeding 1500 W, we recommend to

fit a plug to BS4343 standard.

Using an extension cable

If an extension cable is required, use an approved extension cable suitable

for the power input of this tool (see technical data). The minimum

conductor size is 1.5 mm

When using a cable reel, always unwind the cable completely.

Also refer to the table below.

Conductor size (mm

) Cable rating (Amperes)

0.75 6

1.00 10

1.50 15

2.50 20

4.00 25

Cable length (m)

7.5 15 25 30 45 60

Voltage Amperes Cable rating (Amperes)

115 0 - 2.0 6 6 6 6 6 10

2.1 - 3.4 6 6 6 6 15 15

3.5 - 5.0 6 6 10 15 20 20

5.1 - 7.0 10 10 15 20 20 25

7.1 - 2.0 15 15 20 25 25 -

12.1 - 20.0 20 20 25 - - -

230 0 - 2.0 6 6 6 6 6 6

2.1 - 3.4 6 6 6 6 6 6

3.5 - 5.0 6 6 6 6 10 15

5.1 - 7.0 10 10 10 10 15 15

7.1 - 12.0 15 15 15 15 20 20

12.1 - 20.0 20 20 20 20 25 -

1 2 ... 21 22 23 24 25 26 27 28 29 30 31 ... 107 108

Comments to this Manuals

No comments

DeWalt DW703 Service Manual Page 26

Comments to this Manuals

Related products and manuals for Circular saws DeWalt DW703