DeWalt DCD710-XE Instruction Manual download pdf (Page 5)

• Replacement of the supply cord. If the supply cord is damaged, it must be

replaced by the manufacturer or an authorised DEWALT Service Centre in order

to avoid a hazard.

Extension Cords

CAUTION: Use only extension cords that are approved by the country’s Electrical

Authority. Before using extension cords, inspect them for loose or exposed wires,

damaged insulation and defective fittings. Replace the cord if necessary.

MINIMUM GAUGE FOR CORD SETS

For Cable length (m): 7.5 15 25 30 45 60

Use Cable with minimum rating (Amperes)

Tool Amperes

0 - 3.4 7.5 7.5 7.5 7.5 7.5 7.5

3.5 - 5.0 7.5 7.5 7.5 7.5 10 15

5.1 - 7.0 10 10 10 10 15 15

7.1 - 12.0 15 15 15 15 20 20

12.1 - 20.0 20 20 20 20 25 –

ADDITIONAL SPECIFIC SAFETY RULES

• Wear ear protectors with impact drills. Exposure to noise can cause hearing

loss.

• Use auxiliary handles supplied with the tool. Loss of control can cause personal

injury.

• Hold power tools by insulated gripping surfaces when performing an

operation where the cutting tool may contact hidden wiring or its own cord.

Contact with a “live” wire will make exposed metal parts of the tool “live” and

shock the operator.

• Use clamps or another practical way to secure and support the workpiece to a

stable platform. Holding the work by hand or against your body leaves it unstable

and may lead to loss of control.

• Air vents often cover moving parts and should be avoided. Loose clothes,

jewelry or long hair can be caught in moving parts..

WARNING: ALWAYS wear approved protective safety equipment complying with

the following standards:

• Eye protection: AS/NZS1337 Eye Protectors for Industrial Applications;

• Hearing protection: AS/NZS1270 Acoustics – Hearing Protection;

• Respiratory protection: AS/NZS1716 Respiratory Protective Devices.

WARNING: Some dust created by power sanding, sawing, grinding, drilling, and

other construction activities contains chemicals known to cause cancer, birth defects

or other reproductive harm. Some examples of these chemicals are:

• lead from lead-based paints,

• crystalline silica from bricks and cement and other masonry products, and

• arsenic and chromium from chemically-treated lumber.

Your risk from these exposures varies, depending on how often you do this type of

work. To reduce your exposure to these chemicals: work in a well ventilated area, and

work with approved safety equipment, such as those dust masks that are specially

designed to filter out microscopic particles.

• Avoid prolonged contact with dust from power sanding, sawing, grinding,

drilling, and other construction activities. Wear protective clothing and wash

exposed areas with soap and water. Allowing dust to get into your mouth, eyes,

or lay on the skin may promote absorption of harmful chemicals.

WARNING: Use of this tool can generate and/or disburse dust, which may cause

serious and permanent respiratory or other injury. Always use NIOSH/OSHA approved

respiratory protection appropriate for the dust exposure. Direct particles away from

face and body.

WARNING: We recommend the use of a residual current device with a residual

current rating of 30mA or less.

WARNING: Always wear proper personal hearing protection that conforms to

AS/NZS1270 during use. Under some conditions and duration of use, noise from this

product may contribute to hearing loss.

CAUTION: When not in use, place tool on its side on a stable surface where it

will not cause a tripping or falling hazard. Some tools with large battery packs will

stand upright on the battery pack but may be easily knocked over.

• The label on your tool may include the following symbols. The symbols and their

definitions are as follows:

V ................. volts A ...............amperes

Hz ............... hertz W ..............watts

min ............. minutes ...........alternating current

1 2 3 4 5 6 7 8 9 10 ... 15 16

Comments to this Manuals

No comments

DeWalt DCD710-XE Instruction Manual Page 5

Comments to this Manuals

Related products and manuals for Power tools DeWalt DCD710-XE