DeWalt DCS380-XE Instruction Manual download pdf

INSTRUCTION MANUAL

DW304P-XE

VS RECIPROCATING SAW

DEWALT Industrial Tool Co.,

701 East Joppa Road, Baltimore, MD 21286 • 20 Fletcher Road, Mooroolbark, VIC 3138 Australia

EWALT

The following are trademarks for one or more D

EWALT power tools: the yellow and black color scheme; the “D” shaped

air intake grill; the array of pyramids on the handgrip; the kit box configuration; and the array of lozenge-shaped humps

on the surface of the tool.

IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS OR ANY DEWALT TOOL, CALL US AT: 1800 654 155 (Aust)

or 09 526 2556 (NZ).

SAFETY INSTRUCTIONS FOR POWER TOOLS

When using power tools, always observe the safety regulations applicable in your country to reduce the risk of fire, electric

shock and personal injury. Read the following safety instructions before attempting to operate this product. Keep these

instructions in a safe place.

General Safety Rules

WARNING! Read all instructions. Failure to follow all instructions listed below may result in electric shock, fire and/or

serious injury. The term “power tool” in all of the warnings listed below refers to your mains operated (corded) power tool

or battery operated (cordless) power tool.

SAVE THESE INSTRUCTIONS

1. WORK AREA

a. Keep work area clean and well lit. Cluttered and dark areas invite accidents.

b. Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases

or dust. Power tools create sparks which may ignite the dust or fumes.

c. Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control.

2. ELECTRICAL SAFETY

a. Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs

with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of electric shock.

b. Avoid body contact with earthed or grounded surfaces such as pipes, radiators, ranges and refrigerators.

There is an increased risk of electric shock if your body is earthed or grounded.

c. Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of

electric shock.

d. Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord

away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric

shock.

e. When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord suit-

able for outdoor use reduces the risk of electric shock.

3. PERSONAL SAFETY

a. Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a

power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inatten-

tion while operating power tools may result in serious personal injury.

b. Use safety equipment. Always wear eye protection. Safety equipment such as dust mask, non-skid safety

shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries.

c. Avoid accidental starting. Ensure the switch is in the off position before plugging in. Carrying power tools

with your finger on the switch or plugging in power tools that have the switch on invites accidents.

d. Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a

rotating part of the power tool may result in personal injury.

e. Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool

in unexpected situations.

f. Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves away from

moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.

g. If devices are provided for the connection of dust extraction and collection facilities, ensure these are

connected and properly used. Use of these devices can reduce dust related hazards.

4. POWER TOOL USE AND CARE

a. Do not force the power tool. Use the correct power tool for your application. The correct power tool will do

the job better and safer at the rate for which it was designed.

b. Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled

with the switch is dangerous and must be repaired.

c. Disconnect the plug from the power source before making any adjustments, changing accessories, or

storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally.

d. Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool

or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users.

e. Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and any other

condition that may affect the power tools operation. If damaged, have the power tool repaired before use.

Many accidents are caused by poorly maintained power tools.

f. Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to

bind and are easier to control.

g. Use the power tool, accessories and tool bits etc., in accordance with these instructions and in the manner

intended for the particular type of power tool, taking into account the working conditions and the work to be

performed. Use of the power tool for operations different from those intended could result in a hazardous situation.

5. SERVICE

a. Have your power tool serviced by a qualified repair person using only identical replacement parts. This will

ensure that the safety of the power tool is maintained.

Electrical Safety

The electric motor has been designed for one voltage only. Always check that the power supply corresponds to the volt-

age on the rating plate. 230 V AC means your tool will operate on alternating current. As little as 10% lower voltage can

cause loss of power and can result in overheating. All D

EWALT tools are factory tested; if this tool does not operate,

check the power supply. Your D

EWALT tool is double insulated, therefore no earth wire is required.

• Young children and the infirm. This appliance is not intended for use by young children or infirm persons without

supervision. Young children should be supervised to ensure that they do not play with this appliance.

• Replacement of the supply cord. If the supply cord is damaged, it must be replaced by the manufacturer or an

authorised D

EWALT Service Centre in order to avoid a hazard.

Extension Cords

CAUTION: Use only extension cords that are approved by the country’s Electrical Authority. Before using extension

cords, inspect them for loose or exposed wires, damaged insulation and defective fittings. Replace the cord if necessary.

Additional Safety Instructions

• Hold tool by insulated gripping surfaces when performing an operation where the cutting tool may contact

hidden wiring or its own cord. Contact with a “live” wire will make exposed metal parts of the tool “live” and

shock the operator.

• Do not operate this tool for long periods of time. Vibration caused by the operating action of this tool may cause

permanent injury to fingers, hands, and arms. Use gloves to provide extra cushion, take frequent rest periods, and

limit daily time of use.

WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains

chemicals known to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:

• lead from lead-based paints,

• crystalline silica from bricks and cement and other masonry products, and

• arsenic and chromium from chemically-treated lumber (CCA).

Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these

chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are

specially designed to filter out microscopic particles.

• Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling, and other construction

activities. Wear protective clothing and wash exposed areas with soap and water. Allowing dust to get into

your mouth, eyes, or lay on the skin may promote absorption of harmful chemicals.

WARNING: Use of this tool can generate and/or disburse dust, which may cause serious and permanent respiratory or

other injury. Always use NIOSH/OSHA approved respiratory protection appropriate for the dust exposure. Direct particles

away from face and body.

CAUTION: Wear appropriate personal hearing protection during use. Under some conditions and duration of use,

noise from this product may contribute to hearing loss.

• The label on your tool may include the following symbols. The symbols and their definitions are as follows:

V ................volts A ..............amperes

Hz................hertz W ..............watts

min..............minutes ..........alternating current

..........direct current

o..............no load speed

..............Class II Construction ............earthing terminal

..............safety alert symbol .../min........revolutions per minute

sfpm............surface feet per minute

SAVE THESE INSTRUCTIONS

Switch (Variable Speed) (Fig. 1)

The variable speed trigger switch (A) will give added versatility.

To turn the saw “ON”, first press the small lock-off button (B) on the side of the handle and then depress the trigger (A).

The further the trigger is depressed the higher the speed of the saw.

To turn the saw “OFF” release the trigger (A).

Blade Clamping (Fig. 2)

CAUTION: TURN OFF AND UNPLUG SAW.

To install blade into saw:

1. Loosen set screw(B).

2. Insert blade shank (C) from the front between the reciprocating shaft (D) and the blade clamp(E). Locate hole in

blade (F) over pin (G) on reciprocating shaft.

3. Tighten set screw. If the blade should break off and the shank does not come out of the clamp, be sure the set

screw is loose and eject the shank with a nail or pointed object.

CAUTION: THE BLADE GUARD IS THERE FOR YOUR SAFETY. DO NOT REMOVE IT

Blade Clamp Release Lever DW304P-XE (Fig. 2)

CAUTION: TURN OFF AND UNPLUG SAW.

To install blade into saw:

1. Pull blade clamp release lever (H) up.

2. Insert blade shank from the front.

3. Push blade clamp release lever down.

To remove blade from saw:

1. Open blade clamp release lever.

2. Remove blade.

CAUTION: THE BLADE GUARD IS THERE FOR YOUR SAFETY. DO

NOT REMOVE IT.

Cutting with Blade in Horizontal Position (Fig. 3, 3A)

Installing a blade in the horizontal orientation allows cutting close to floors, walls or ceilings where limited clearance is

available. Ensure that the Blade Guard is pressed against the framing to avoid kickback.

Flush-To Cutting (Fig. 4)

The compact design of the saw motor housing and spindle housing permits extremely close cutting to floors, corners

and other difficult areas.

CAUTION: When sawing into walls, floors or

wherever “live” electrical wires may be encountered, DO NOT TOUCH ANY FRONT METAL PARTS OF THE TOOL! Hold

the tool only by the plastic handle and housing to prevent electric shock if you saw into a “live” wire.

CAUTION: Always wear eye protection while operating this power tool.

Wood Cutting (Fig. 5)

Before cutting any type of wood, be sure it is firmly anchored or clamped to prevent slipping. Place blade lightly against

work to be cut, switch on saw motor and allow it to obtain maximum speed before applying pressure. Always hold saw

firmly with both hands while cutting. Whenever possible, the saw shoe must be held firmly against the material being

cut. This will prevent the saw from jumping or vibrating and minimize blade breakage.

FIG. 2

FIG. 1

1 2

Summary of Contents

Page 1 - VS RECIPROCATING SAW

INSTRUCTION MANUALDW304P-XEVS RECIPROCATING SAWDEWALT Industrial Tool Co., 701 East Joppa Road, Baltimore, MD 21286 • 20 Fletcher Road, Mooroolbark,

Page 2

Metal Cutting (Fig. 6)This unit has different metal cutting capacities depending upon type of blade used and the metal to be cut. Use a finerblade for

Comments to this Manuals

No comments

DeWalt DCS380-XE Instruction Manual

Browse online or download Instruction Manual for Power tools DeWalt DCS380-XE. DeWalt DCS380-XE Instruction manual User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Power tools DeWalt DCS380-XE