DeWalt DCD985B Use and Care Manual Page 12
- Page / 56
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
10
English
SCREWDRIVING (FIG. 4)
Rotate the mode control collar (F) so the screw symbol is aligned
with the arrow.
NOTE: The torque adjustment collar may be set to any number at any
time. However, the torque adjustment collar is only engaged during
screwdriving mode and not in drill and hammerdrill modes.
HAMMERDRILLING (FIG. 5)
CAUTION: When the mode collar is in the drill/hammerdrill mode,
the drill will not clutch out regardless of the position of the torque
adjustment collar (E).
Rotate the mode control collar (F) so the hammer symbol is aligned
with the arrow.
NOTE: The torque adjustment collar (E) may be set on any number.
E
F
G
SCREWDRIVING
HAMMERDRILLING
DRILLING
E
F
G
FIG. 5
FIG. 4
FIG. 3
Forward/Reverse Control Button (Fig. 2)
A forward/reverse control button (B) determines the direction of the
tool and also serves as a lock-off button.
To select forward rotation, release the trigger switch and depress the
for ward/re verse control button on the right side of the tool.
To select reverse, release the trigger switch and depress the forward/
reverse control button on the left side of the tool.
The center position of the control button locks the tool in the OFF
position. When changing the position of the control button, be sure
the trigger is released.
NOTE: The first time the tool is run after changing the direction of
rotation, you may hear a click on start up. This is normal and does not
indicate a problem.
Worklight (Fig. 2)
There is a worklight (C) located just above the trigger switch (A). The
worklight is activated when the trigger switch is depressed, and will
automatically turn off 20 seconds after the trigger switch is released.
If the trigger switch remains depressed, the worklight will remain on.
NOTE: The worklight is for lighting the immediate work surface and is
not intended to be used as a flashlight.
Mode Control Collar (Fig. 3–5)
Your drill is equipped with a separate mode control collar (F) to switch
between drilling, screwdriving and hammerdrilling mode.
DRILLING (FIG. 3)
CAUTION: When the mode collar is in the drill/hammerdrill mode,
the drill will not clutch out regardless of the position of the torque
adjustment collar (E).
Rotate the mode control collar (F) so the drill symbol is aligned with
the arrow.
NOTE: The torque adjustment collar (E) may be set on any number.
- EWALT • www.dewalt.com 1
- FOR FUTURE REFERENCE 3
- Battery Packs 6
- READ ALL INSTRUCTIONS 6
- The RBRC™ Seal 7
- Battery Chargers 7
- Indicator Light Operation 9
- Charge Indicators 9
- Chargers 9
- Charging Procedure (Fig. 1) 9
- Storage Recommendations 10
- Important Charging Notes 10
- Worklight (Fig. 2) 12
- OPERATION 14
- (Fig. 9) 14
- Screwdriving (Fig. 4) 15
- Hammerdrilling (Fig. 5) 15
- Drilling (Fig. 3) 15
- MAINTENANCE 16
- Cleaning 16
- Accessories 16
- Three Year Limited Warranty 17
- EWALT, COMPOSEZ LE NUMÉRO 18
- EWALT (1-800-433-9258) 18
- Français 19
- LIRE TOUTES LES CONSIGNES 22
- Le sceau SRPRC 23
- Chargeurs 25
- Procédure de charge (Fig.1) 25
- Fonctionnement du voyant 26
- Voyants de charge 26
- Recommandations de stockage 27
- CONSERVER CES CONSIGNES POUR 27
- UTILISATION ULTÉRIEURE 27
- Poignée latérale (Fig. 2) 28
- DESCRIPTION (Fig. 2) 28
- Lampe de travail (Fig.2) 29
- Trois vitesses (Fig. 3–5) 30
- (Fig. 6–8) 30
- FONCTIONNEMENT 31
- Perçage (Fig. 3) 32
- Mode visseuse (Fig. 4) 32
- ENTRETIEN 33
- Nettoyage 33
- Accessoires 33
- Réparations 34
- Garantie limitée de trois ans 34
- EWALT, LLÁMENOS AL NÚMERO 36
- LEA TODAS LAS INSTRUCCIONES 40
- El sello RBRC™ 41
- Cargadores 43
- Indicadores de carga 44
- GUARDE ESTAS INSTRUCCIONES 45
- PARA VOLVER A CONSULTAR 45
- EN EL FUTURO 45
- Mango lateral (Fig. 2) 46
- COMPONENTES (Fig. 2) 46
- Taladrado (Fig. 3) 50
- Destornillado (Fig. 4) 51
- MANTENIMIENTO 52
- Limpieza 52
- Accesorios 52
- Reparaciones 52
- Póliza de Garantía 53
- ESPECIFICACIONES 55
- 120 Volts 12 Volts 56
Related products and manuals for Cordless combi drills DeWalt DCD985B
(56 pages)© 2020, manymanuals.com. All rights reserved. | 1.261 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals