DeWalt D51238 Service Manual download pdf (Page 21)

ENGLISH

6. Do not overreach.

Keep proper footing and balance at all times.

7. Stay alert.

Watch what you are doing. Use common sense.

Do not operate the tool when you are tired.

8. Use appropriate tool.

The intended use is described in this instruction

manual. Do not force small tools or attachments

to do the job of a heavy-duty tool. The tool will

do the job better and safer at the rate for which it

was intended.

WARNING! The use of any accessory or

attachment or performance of any operation with

this tool, other than those recommended in this

instruction manual, may present a risk of personal

injury.

9. Maintain tools with care.

Keep the tools in good condition and clean

for better and safer performance. Follow the

instructions for maintenance and changing

accessories. Keep all controls dry, clean and free

from oil and grease.

10. Check for damaged parts.

Before using the tool, carefully check it for damage

to ensure that it will operate properly and perform

its intended function. Check for misalignment and

seizure of moving parts, breakage of parts and

any other conditions that may affect its operation.

Have damaged guards or other defective parts

repaired or replaced as instructed.

11. Have your tool repaired by an authorised

DEWALT repair agent.

This tool is in accordance with the relevant safety

regulations. To avoid danger, tools must only be

repaired by qualified technicians.

Additional safety instructions for pneumatic nailers

• Always wear safety glasses.

• Always wear ear protection.

• Only use fasteners of the type speciﬁ ed in

the manual.

• Do not use any stands for mounting the tool to

a support.

• Never use the tool for any other purpose than

speciﬁ ed in this manual.

• Prior to each operation check that the safety and

triggering mechanism is functioning properly and

that all nuts and bolts are tight.

• Use quick-action couplings for connection to

the compressed air system. The non-sealable

nipple must be ﬁ tted to the tool in such a way

that no compressed air remains in the tool after

disconnection.

• Always use clean, dry compressed air. Do not

use oxygen or combustible gases as an energy

source for this tool.

• Only connect this tool to an air supply where

the maximum allowable pressure of the tool

cannot be exceeded by more than 10%. In case

of higher pressures, a pressure reducing valve

including a downstream safety valve shall be built

into the compressed air supply.

• Only use hoses with a rating exceeding the

maximum operating pressure of the tool.

• Before transporting the tool, disconnect it from

the compressed air system, especially where

ladders are used or where unusual physical

posture is adopted while moving.

• Disconnect the tool from the air supply when it is

not in use.

• Avoid weakening or damaging the tool, for

example by:

– punching or engraving

– modiﬁ cations not authorised by the manufacturer

– guiding against templates made of hard

material such as steel

– dropping or pushing across the ﬂ oor

– applying excessive force of any kind

• Do not use the equipment as a hammer.

• Never point any operational fastener driving tool

at yourself or at any other person.

• While working, hold the tool in such a way that

no injuries can be caused to the head or to the

body in the event of a possible recoil due to a

disruption in the energy supply or hard areas

within the workpiece.

• Never actuate the fastener driving tool into free

space.

• In the work area, carry the tool at the workplace

using only one handle, and never with the trigger

actuated.

• Consider the conditions in the work area.

Fasteners can penetrate thin workpieces or slip

off corners and edges of the workpiece, and thus

put people at risk.

• Do not drive fasteners close to the edge of the

workpiece.

1 2 ... 16 17 18 19 20 21 22 23 24 25 26 ... 107 108

Comments to this Manuals

No comments

DeWalt D51238 Service Manual Page 21

Comments to this Manuals

Related products and manuals for Nail Gun DeWalt D51238